6032HTS
Institutional Tub and Shower
| Length | 60 1⁄4" | 1530mm |
| Width | 32 3⁄4" | 832mm |
Download Spec Sheet
Tub/shower unit shall be a VENCO Model No.6032HTS. Finished surface shall be of a Premium sanitary-grade polyester Gelcoat with a minimal thickness of 15 dry mills and a finished cured Barcol hardness of 80-90. The unit shall have dimensions of 60 1⁄4" x 32 3⁄4" x 72 3⁄4" O.D. with build-in soap & shampoo shelf.
Sides and back of unit shall be constructed of molded reinforced fiberglass with 15% minimum fiberglass content plus an inner core of 7/16" Wafer board and is laminated with another layer of reinforced fiberglass for superior overall rigidity. The approximate weight of the unit shall be 178lbs.
Above-the-floor installation of waste, overflow and drain, for Silent Floor Installations.
Stainless Steel Grab Bar
The unit shall have two (2) stainless steel grab bars mounted horizontally on the back wall. One (1) stainless steel grab bar mounted horizontally on valve wall. One (1) stainless steel grab bar mounted horizontally on the dry wall. All stainless steel grab bars will be 1 1⁄4" O.D. 18 gauge type #304 stainless steel, mounted with stainless steel nuts, bolts and washers. Fastened from the back side of the unit and sealed and caulked to meet ASTM F-466 specifications. All stainless steel Grab Bars meet Federal Specification WW-P541/8b, Amendment 1, 16 April, 1990; ANSI 117.1 and All A.D.A. CODE REQUIREMENTS. These bars, when properly installed, meet the 900lb. downward pull requirement for Federal Specification work, F.H.A., V.A., HOSPITAL CODES AND PRIVATE CONSTRUCTION.
Fold-up Seat
This unit shall include a White Phenolic Seat that meet Fed. Spec. WW-P-541/8b, Amendment 1, April, 1990 and ANSI 117.1. When properly installed this seat is designed and manufactured to exceed all applicable federal load specifications and comply with all A.D.A. Requirements. The Seat frame is Type 304 (18-8) stainless steel tubing, 11⁄4" x 18 ga. square main frame with 1" x 18 ga. round cross members. The Folding Tub Seat is Wall mounted at one end with two (2) swing hinges and supported in a down position by the tub edge. White Phenolic 1⁄2" thick x 3" wide slats.
Click images below to view additional images
This unit is designed to comply with: ANSI A117.1 - 1992, ADA The Americans With Disabilities Act-1991, C.S.A. APPROVED. Warranty is to the original purchaser only, that this unit is free from manufacturing defects in material or workmanship for a period of five (5) years from date of installation.
The Addition of grab bars or fixtures not properly installed by purchaser shall void this warranty.
Standard Accessories Installed
4 - 24" - 11⁄4" S. S. Grab Bars
1 - White Phenolic Fold-up Seat
Optional Accessories
1 - Curtain Rod: Stainless Steel, 18 ga. 1" O.D., with mounting flanges.
1 - Shower Curtain: Vinyl, 10 ga. flame resistant, white, chain-weighted.
1 - Pressure Balance Mixing Valve, lever handle, polished chrome finish.
1 - Hand Shower, Push Button on/off, Hand Held Shower with 84" hose, Vacuum breaker.
1 - Tub spout with diverter, polished chrome finish.
The Addition of grab bars or fixtures not properly installed by purchaser shall void this warranty.
Standard Accessories Installed
4 - 24" - 11⁄4" S. S. Grab Bars
1 - White Phenolic Fold-up Seat
Optional Accessories
1 - Curtain Rod: Stainless Steel, 18 ga. 1" O.D., with mounting flanges.
1 - Shower Curtain: Vinyl, 10 ga. flame resistant, white, chain-weighted.
1 - Pressure Balance Mixing Valve, lever handle, polished chrome finish.
1 - Hand Shower, Push Button on/off, Hand Held Shower with 84" hose, Vacuum breaker.
1 - Tub spout with diverter, polished chrome finish.
